English
FrançaisRegulations
Page 12 of 140, showing 20 records out of 2786 total, starting on record 221, ending on 240
| Title | Description | Implementation date | Source | Publication | Created |
|---|---|---|---|---|---|
| US EAS 491:2008, Incineration plant for the destruction of hospital waste — Specification | This Uganda Standard specifies the performance requirements for incineration plant, assisted by auxiliary fuel if required, suitable for the destruction of hospital waste. Devices which utilize intensities of combustion exceeding an average heat release rate of 350 W/m3 are not included. This standard does not specify materials or methods of construction. | 2017-02-03 | The Uganda National Bureau of standards | The Uganda Gazette, Vol. CX No. 7 | 22 March 2017 |
| US IEC 60228:2004, Conductors of insulated cables | This Uganda Standard specifies the nominal cross-sectional areas, in the range 0.5 mm2 to 2 500 mm2, for conductors in electric power cables and cords of a wide range of types. Requirements for numbers and sizes of wires and resistance values are also included. (This Uganda Standard cancels and replaces, US EAS 501:2008, Conductors of insulated cables, which has been republished). | 2015-08-07 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVIII No. 43 of 7 August 2015 | 23 August 2016 |
| US ISO 17842-2:2015, Safety of amusement rides and amusement devices — Part 2: Operation and use | This Uganda Standard specifies the minimum requirements necessary to ensure the safe maintenance, operation, inspection and testing of the following: mobile, temporary or permanently installed machinery and structures, e.g. roundabouts, swings, boats, ferris wheels, roller coasters, chutes, grandstands, membrane or textile structures, booths, stages, side shows, and structures for artistic aerial displays. | 2015-08-07 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVIII No. 43 of 7 August 2015 | 25 August 2016 |
| US ISO 9809-4:2014, Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 4: Stainless steel cylinders with an Rm value of less than 1 100 MPa | This Uganda Standard specifies the minimum requirements for the material, design, construction and workmanship, manufacturing processes, examinations, and tests at manufacture of refillable seamless stainless steel gas cylinders of water capacities from 0.5 l up to and including 150 l for compressed, liquefied, and dissolved gases. This part of US ISO 9809 is applicable to cylinders with a maximum actual tensile strength, Rma, of less than 1 100 MPa. | 0000-00-00 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 10380:2012, Pipework — Corrugated metal hoses and hose assemblies | This Uganda Standard specifies the minimum requirements for the design, manufacture, testing and installation of corrugated metal hoses and metal hose assemblies | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| ISO 4641:2010, Rubber hoses and hose assemblies for water suction and discharge — Specification | This Uganda Standard specifies the minimum requirements for textile-reinforced, smooth-bore rubber water-suction and discharge hoses and hose assemblies. Three types of hoses and hose assemblies are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges: ambient temperatures: −25 °C to +70 °C; andwater temperatures during operation: 0 °C to +70 °C. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 22 September 2016 |
| US ISO 1413:1984, Horology — Shock resistant watches | This Uganda Standard specifies the minimum requirements for shock-resistant watches and describes the corresponding method of test. It is intended to allow homologation testing of watches rather than the individual control of all watches of a production batch. Indeed, assuming that each watch could comply with the minimum requirements without apparent damage, readjustment could still be made necessary because the test can lead to an alteration of the initial rate of a watch. This standard is based on the simulation of the shock received by a watch on falling accidentally from a height of 1 m on to a horizontal hardwood surface. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 03 October 2016 |
| US ISO 5771:2008, Rubber hoses and hose assemblies for transferring anhydrous ammonia — Specification | This Uganda Standard specifies the minimum requirements for rubber hoses used for transferring ammonia, in liquid or in gaseous form, at ambient temperatures from −40 °C up to and including +55 °C. It does not include specifications for end fittings, but is limited to the performance of the hoses and hose assemblies. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 13691:2001, Petroleum and natural gas industries — High-speed special-purpose gear units | This Uganda Standard specifies the minimum requirements for enclosed, precision, single and double helical, one- and two-stage speed increasers and reducers of parallel shaft design with pinion speeds of 3000 min−1 or greater, or pitch line velocities of 25 m/s or greater, for special purpose applications. | 2017-02-03 | The Uganda National Bureau of standards | The Uganda Gazette, Vol. CX No. 7 | 22 March 2017 |
| US ISO 4706:2008, Gas cylinders — Refillable welded steel cylinders — Test pressure 60 bar and below | This Uganda Standard specifies the minimum requirements concerning material selection, design, construction and workmanship, procedure and test at manufacture of refillable welded-steel gas cylinders of a test pressure not greater than 60 bar1), and of water capacities from 0.5 l up to and including 500 l exposed to extreme worldwide temperatures (-50 °C to 65 °C) used for compressed, liquefied or dissolved gases. Transportable large cylinders of water capacity above 150 l and up to 500 l may be manufactured and certified to this standard provided handling facilities are provided. This standard is primarily intended to be used for industrial gases other than Liquefied Petroleum Gas (LPG), but may also be applied for LPG. For specific LPG applications see ISO 22991. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 764:2002, Horology — Magnetic resistant watches | This Uganda Standard specifies the minimum requirements and test methods for magnetic resistant watches. It is based on the simulation of an accidental exposure of a watch to a direct current magnetic field of 4 800 A/m. Annex A deals with watches designated as magnetic resistant with an additional indication of intensity of a magnetic field exceeding 4 800 A/m. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 03 October 2016 |
| US ISO 10425:2003, Steel wire ropes for the petroleum and natural gas industries — Minimum requirements and terms of acceptance | This Uganda Standard specifies the minimum requirements and terms of acceptance for the manufacture and testing of steel wire ropes not exceeding rope grade 2160 for the petroleum and natural gas industries. | 2017-02-03 | The Uganda National Bureau of standards | The Uganda Gazette, Vol. CX No. 7 | 22 March 2017 |
| US ISO 6361-2:2014, Wrought aluminium and aluminium alloys — Sheets, strips and plates — Part 2: Mechanical properties | This Uganda Standard specifies the mechanical properties of wrought aluminium and aluminium alloy sheets, strips, and plates for general engineering applications. It applies to flat-rolled products. | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US ISO 6362-2:2014, Wrought aluminium and aluminium alloys — Extruded rods/bars, tubes and profiles — Part 2: Mechanical properties | This Uganda Standard specifies the mechanical properties of wrought aluminium and aluminium alloy extruded rods/bars, tubes, and profiles for general engineering applications. It applies to extruded products. | 2016-08-12 | National Forest Authority | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US ISO 9090:1989, Gas tightness of equipment for gas welding and allied processes | This Uganda Standard specifies the maximum external leakage rates which are acceptable for equipment used for welding, cutting and allied processes. It applies to individual components which are used in the gas supply to a blowpipe from the connecting point of the hose (outlet of the cylinder valve or connecting point to a gas supply plant). It does not apply to gas supply plants. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 9539:2010, Gas welding equipment — Materials for equipment used in gas welding, cutting and allied processes | This Uganda Standard specifies the general, and some of the special, requirements on materials used for the construction of equipment used in gas welding, cutting and allied processes. Additional requirements on materials for some equipment are given in other standards. This standard is not applicable to materials used for the construction of welding hoses which are specified in US ISO 3821. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 29 September 2016 |
| US ISO 1461:2009, Hot dip galvanized coatings on fabricated iron and steel articles — Specification and test methods | This Uganda Standard specifies the general properties of coatings and test methods for coatings applied by dipping fabricated iron and steel articles (including certain castings) in a zinc melt (containing not more than 2 % of other metals). | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US ISO 23560: 2015, Woven polypropylene sacks for bulk packaging of foodstuffs | This Uganda Standard specifies the general characteristics, requirements, and methods of test for woven polypropylene (PP) sacks. It is applicable to woven PP sacks, having a capacity of 50 kg or 25 kg, intended for the transport and storage of foodstuffs, such as cereals, sugar, and pulses. | 2015-12-15 | The Uganda National Bureau of standards | The Uganda Gazette 22 January 2016: General Notice No. 45 of 2016 | 08 August 2016 |
| US ISO 10225:2013, Gas welding equipment — Marking for equipment used for gas welding, cutting and allied processes | This Uganda Standard specifies the gas letter code to be used for marking the equipment for gas welding, cutting and allied processes, when the full name of the gas cannot be used. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 29 September 2016 |
| US ISO 5019-5:1984, Refractory bricks — Dimensions — Part 5: Skewbacks | This Uganda Standard specifies the dimensions of two skewbacks, one for use with bricks of a course height 64 mm and one for use with bricks of a course height 76 mm. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 17 September 2016 |
