English
FrançaisRegulations
Page 31 of 140, showing 20 records out of 2786 total, starting on record 601, ending on 620
| Title | Description | Implementation date | Source | Publication | Created |
|---|---|---|---|---|---|
| US ISO 11425:1996, Rubber hoses and hose assemblies for automobile power steering systems — Specification | This Uganda Standard specifies requirements for five types of hose and hose assembly used in automobile power-steering systems, the five types differing in their pressure ratings and volumetric expansion. They are for use with fluids in the temperature range - 40 “C to + 135 “C. This standard is based on performance tests and, in order to take account of technological developments, no requirements are included for specific materials, detailed construction or manufacturing methods. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 12170:1996, Gas welding equipment — Thermoplastic hoses for welding and allied processes | This Uganda Standard specifies the requirements and relevant methods of measurement and testing of two types of thermoplastic hoses with maximum design working pressure of 1 MPa and of 2 MPa, used for flexible gas supply lines in specific fields of application as follows:small kits for brazing and welding in accordance with US ISO 14112;air-aspirated blowpipes for welding and allied processes;miniature welding such as jewellery work, dental work excluding acetylene applications; andarc welding with shielding gas. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 13363:2004, Rubber and plastics hoses for marine engine wet-exhaust systems — Specification | This Uganda Standard specifies requirements for three types and two classes of hose. The hoses are intended for use in marine-engine wet-exhaust systems (where the exhaust gases are mixed with the discharge of cooling water).The three types are:type 1: a softwall hose, made of oil-resistant material, with a synthetic-fabric reinforcement;type 2: a hardwall hose, made of oil-resistant material, with a synthetic-fabric reinforcement with a helical wire embedded in it; andtype 3: a hose or tube (flexible connector), made of oil-resistant material, with or without a reinforcement or cover, intended for use in short lengths in locations where the connector is protected from mechanical damage.The two classes are:class A intended for diesel engines; andclass B intended for petrol engines, and for diesel engines with a very high exhaust temperature | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 14113:2013, Gas welding equipment — Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) | This Uganda Standard specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied, and dissolved gases up to a maximum working pressure of 450 bar (45 MPa), within the ambient temperature range of −20 °C to +60 °C. This standard applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage. This standard does not cover rubber or thermoplastic hoses for welding, cutting, and allied processes (see US ISO 3821 and US ISO 12170). This standard does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 14557:2002, Fire-fighting hoses — Rubber and plastics suction hoses and hose assemblies | This Uganda Standard gives requirements and test methods for rubber and plastics suction hoses for fire-fighting purposes. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 15465:2004, Pipework — Stripwound metal hoses and hose assemblies | This Uganda Standard specifies the requirements for the design, manufacture and testing of four principal types of stripwound metal hose and hose assemblies, of which only one type is for pressure applications. The four are: single overlap, unpacked and packed; double overlap, unpacked and packed, the last of these having maximum allowable pressures of up to 40 bar. These hoses and hose assemblies may be supplied in nominal sizes from DN 6 to DN 500 and may operate at temperatures up to 600 °C dependent on materials of construction | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 16438:2012, Agricultural irrigation equipment — Thermoplastic collapsible hoses for irrigation — Specifications | This Uganda Standard specifies requirements for reinforced and non-reinforced thermoplastic collapsible hoses, which are intended to be used as main and sub-main supply lines for the conveyance and distribution of water for irrigation at water temperatures up to 50 °C. It is applicable to irrigation hoses with nominal diameters between 40 mm and 500 mm and working pressures between 0,3 bar (0,03 MPa) and 6 bar (0,6 MPa). This standard is applicable to two types of hose configurations: distributor hose (with outlet connections) and plain hose (without outlet connections). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 17165-1:2007, Hydraulic fluid power — Hose assemblies — Part 1: Dimensions and requirements | This Uganda Standard specifies requirements for hose assemblies that are manufactured from hoses that conform to US ISO 3949 and to all parts of US ISO 1436, US ISO 3862, US ISO 4079 and US ISO 11237 and hose fittings with elastomeric seals that conform to US ISO 12151-1, US ISO 12151-2, US ISO 12151-3 and ISO 12151-6. This part of US ISO 17165 contains information of the most important criteria for the selection of preferred types of hoses and hose fittings with elastomeric sealing for use in hydraulic fluid power applications. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 23297:2008, Thermoplastics hoses and hose assemblies — Wire or synthetic yarn reinforced single-pressure types for hydraulic applications — Specification | This Uganda Standard specifies requirements for eight classes and two types (construction with adhesive bond between layers and construction without adhesive bond between layers) of wire or synthetic yarn reinforced hydraulic hoses and hose assemblies of nominal size from 3,2 to 31,5. Each class has a single maximum working pressure for all sizes. Such hoses are suitable for use with hydraulic fluids HH, HL, HM, HR, and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C for grades A and B and −40 °C to +120 °C for grades C and D. This standard does not include requirements for end fittings. It is limited to the performance of hoses and hose assemblies. The hose assembly maximum working pressure is governed by the lowest maximum working pressure of the components | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 669:2000, Resistance welding — Resistance welding equipment — Mechanical and electrical requirements | This Uganda Standard applies to resistance welding equipment, to guns with inbuilt transformers and to complete movable welding equipment. The following types are included: • single-phase equipment with alternating welding current; • single-phase equipment with rectified welding current by rectification of the output of the welding transformer; • single-phase equipment with inverter welding transformer; • three-phase equipment with rectified welding current by rectification of the output of the welding transformer; • three-phase equipment with a current rectification in the input of the welding transformer (sometimes called frequency convertor); and • three-phase equipment with inverter welding transformers. This standard applies neither to welding transformers sold separately nor to safety requirements | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 1089:1980, Electrode taper fits for spot welding equipment — Dimensions | This Uganda Standard lays down the taper dimensions and tolerances of electrode taper fits for spot welding electrode , electrode adaptors, electrode holders and similar parts. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 1089:1980, Electrode taper fits for spot welding equipment — Dimensions | This Uganda Standard lays down the taper dimensions and tolerances of electrode taper fits for spot welding electrode , electrode adaptors, electrode holders and similar parts. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 2503:2009, Gas welding equipment — Pressure regulators and pressure regulators with flow-metering devices for gas cylinders used in welding, cutting and allied processes up to 300 bar (30 MPa | This Uganda Standard specifies requirements for single or two-stage pressure regulators without flow metering devices for connection to gas cylinders used for compressed gases up to 300 bar 1) (30 MPa),dissolved acetylene,liquefied petroleum gases (LPG),methylacetylene-propadiene mixtures (MPS), andcarbon dioxide (CO2),for use in welding, cutting and allied processes. It does not cover pressure regulators having a nominal outlet pressure p2 > 20 bar. This standard also specifies requirements for single or two-stage pressure regulators with flow metering devices for connection to gas cylinders used for compressed gases or mixtures up to 300 bar (30 MPa), and carbon dioxide (CO2), for use in welding, cutting and allied processes. This standard does not cover pressure regulators intended for direct use on cylinder bundles. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5171:2009, Gas welding equipment — Pressure gauges used in welding, cutting and allied processes | This Uganda Standard specifies requirements for Bourdon-tube pressure gauges normally used with compressed gas systems at pressures up to 30 MPa (300 bar) in welding, cutting and allied processes. It also covers use for dissolved acetylene and for liquefied gases under pressure. It does not cover gauges for acetylene in acetylene-manufacturing plants | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5172:2006, Gas welding equipment — Blowpipes for gas welding, heating and cutting — Specifications | This Uganda Standard specifies specifications for blowpipes for gas welding, heating and cutting of metals. It applies to manual blowpipes for welding and heating with a nominal thermal power up to 32 000 kcal/h, and manual and machine cutting blowpipes with a cutting range up to 300 mm. This standard does not apply to air-aspirated blowpipes which are covered in US ISO 9012. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5175:1987, Equipment used in gas welding, cutting and allied processes — Safety devices for fuel gases and oxygen or compressed air — General specifications, requirements and tests | This Uganda Standard lays down the general specifications, requirements of safety devices for fuel gases and oxygen or compressed air used downstream of cylinder or pipeline outlet regulators and of pipeline outlet valves, and upstream of blowpipes for welding, cutting and allied processes. lt does not specify location and combination of these devices in the gas system. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5182:2008, Resistance welding — Materials for electrodes and ancillary equipment | This Uganda Standard specifies the characteristics of materials for resistance welding electrodes and ancillary equipment which are used for carrying current and transmitting force to the work. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5183-1:1998, Resistance welding equipment — Electrode adaptors, male taper 1:10 — Part 1: Conical fixing, taper 1:10 | This Uganda Standard specifies the dimensions and tolerances of resistance spot welding electrode adaptors where the fixing element for the cap is a male taper of 1:10 and for which the electrode taper fits in conformance with US ISO 1089. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5183-2:2000, Resistance welding equipment — Electrode adaptors, male taper 1:10 — Part 2: Parallel shank fixing for end-thrust electrodes | This Uganda Standard specifies the dimensions and tolerances of resistance spot welding electrode adaptors where the fixing element for the cap is a male taper of 1:10 and a parallel shaft is used to fix the adaptor to the electrode holder in accordance with US ISO 8430-3. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 5822:1988, Spot welding equipment — Taper plug gauges and taper ring gauges | This Uganda Standard specifies requirements for taper plug and ring gauges used for the checking of type A, B and C tapers according to US ISO 1089. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
