English
FrançaisRegulations
Page 90 of 140, showing 20 records out of 2786 total, starting on record 1781, ending on 1800
| Title | Description | Implementation date | Source | Publication | Created |
|---|---|---|---|---|---|
| US CODEX STAN 17:1981, Standard for canned applesauce | This Uganda Standard applies to canned applesauce offered for direct consumption, including for catering purposes or for repacking if required. It does not apply to the product when indicated as being intended for further processing. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| TZS 1660:2014, Polyurethane (PU) coated leather — Specification | TZS 1660:2014, Polyurethane (PU) coated leather - Specification This standard prescribes requirements, methods of sampling and test for polyurethane (PU) coated leather. | 2014-12-18 | Tanzania Bureau of Standards (TBS) | 14 September 2016 | |
| TZS 1659:2014, Textiles — Reusable sanitary towels — Specification | This Tanzania Standard prescribes the requirements for reusable sanitary towels for external use. | 2014-12-18 | Tanzania Bureau of Standards (TBS) | 14 September 2016 | |
| Code of practice for design and construction | Gives recommendations for the structural use of concrete in buildings and structures, excluding bridges and structural concrete made with high alumina cement. | 1981-06-05 | Standards Assocaition of zimbabwe | 14 September 2016 | |
| Cast-Iron pipes and pipe fittings for use above ground in drainage installations | Covers the requirements for low pressure cast-iron pipes and pipe fit-tings, intended for use above ground as soil water, waste water and vent pipes. | 1981-06-05 | Standards Assocaition of zimbabwe | 14 September 2016 | |
| Components of Pressure Pipe Systems: Unplasticised Poly (Vinyl Chloride) Pressure pipe system | Specifies requirements for unplasticised poly (vinyl chloride) (PVC-U pipes and injection molded fittings intended for above-ground and be-low ground pressure applications for the conveyance of potable water in reticulation systems, and for other applications in which continuous temperatures in excess of 25 oC are not encounted. | 1981-06-05 | Standards Assocaition of zimbabwe | 14 September 2016 | |
| Earthenware drain and sewer pipes and fittings | Covers vitrified clay pipes suitable for jointing by the following meth-ods: mortar caulking; rolling rubber ring; bitumen run; reformed facto-ry-applied; plain-end pipe; slip seal rubber. Jointing methods are not covered in the specification. | 1980-03-07 | 14 September 2016 | ||
| US ISO 11118:1999, Gas cylinders — Non-refillable metallic gas cylinders — Specification and test methods | This Uganda Standard specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes and tests at manufacture of non-refillable metallic gas cylinders of welded, brazed or seamless construction for compressed, liquefied and dissolved gases exposed to extreme worldwide ambient temperatures. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 11114-1:2012, Gas cylinders — Compatibility of cylinders and valve materials with gas contents — Part 1: Metallic materials | This Uganda Standard provides requirements for the selection of safe combinations of metallic cylinder and valve materials and cylinder gas content. The compatibility data given is related to single gases and to gas mixtures. Seamless metallic, welded metallic and composite gas cylinders and their valves, used to contain compressed, liquefied and dissolved gases, are considered. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| Safety Factors and Smoke emission of Domestic Stoves Burning Solid Fuels at a rate not Exceeding 5Kg per hour | Covers the smoke emission and certain safety factors of domestic stoves burning solid fuels. Quality of manufacture and general performance not included. | 1976-07-01 | Standards Assocaition of zimbabwe | 14 September 2016 | |
| US ISO 10461:2005, Gas cylinders — Seamless aluminium-alloy gas cylinders — Periodic inspection and testing | This Uganda Standard deals with seamless aluminium-alloy transportable gas cylinders intended for compressed and liquefied gases under pressure, of water capacity from 0.5 l to 150 l; it also applies, as far as practical, to cylinders of less than 0.5 l water capacity. This standard specifies the requirements for periodic inspection and testing to verify the integrity of such gas cylinders for further service. This standard does not apply to periodic inspection and testing of acetylene cylinders or composite cylinders with aluminium-alloy liners. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 9809-4:2014, Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 4: Stainless steel cylinders with an Rm value of less than 1 100 MPa | This Uganda Standard specifies the minimum requirements for the material, design, construction and workmanship, manufacturing processes, examinations, and tests at manufacture of refillable seamless stainless steel gas cylinders of water capacities from 0.5 l up to and including 150 l for compressed, liquefied, and dissolved gases. This part of US ISO 9809 is applicable to cylinders with a maximum actual tensile strength, Rma, of less than 1 100 MPa. | 0000-00-00 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 9809-3:2010, Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 3: Normalized steel cylinders | This Uganda Standard specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at manufacture of refillable normalized or normalized and tempered seamless steel gas cylinders of water capacities from 0.5 l up to and including 150 l for compressed, liquefied and dissolved gases. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 9809-2:2010, Gas cylinders — Refillable seamless steel gas cylinders —Design, construction and testing — Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa | This Uganda Standard specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at manufacture of refillable quenched and tempered seamless steel gas cylinders of water capacities from 0.5 l up to and including 150 l for compressed, liquefied and dissolved gases. This part of US ISO 9809 is applicable to cylinders with a maximum tensile strength Rma ≥ 1 100 MPa. It is not applicable to cylinders with Rma, max >1 300 MPa for diameters >140 mm and guaranteed wall thicknesses a’ ≥ 12 mm and Rma, max >1 400 MPa for diameters ≤ 140 mm and guaranteed wall thicknesses a’ ≥ 6 mm, because beyond these limits, additional requirements can apply. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 9809-1: 2010, Gas cylinders — Refillable seamless steel gas cylinders — Design, construction and testing — Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa | This Uganda Standard specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes, examination and testing at manufacture of refillable quenched and tempered seamless steel gas cylinders of water capacities from 0.5 l up to and including 150 l for compressed, liquefied and dissolved gases. This standard is applicable to cylinders with a maximum actual tensile strength Rma of less than 1 100 MPa. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 7866:2012, Gas cylinders — Refillable seamless aluminium alloy gas cylinders — Design, construction and testing | This Uganda Standard specifies minimum requirements for the material, design, construction and workmanship, manufacturing processes and tests at time of manufacture of refillable seamless aluminium alloy gas cylinders of water capacities up to and including 150 litres for compressed, liquefied and dissolved gases for worldwide use (normally up to +65 °C). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 4706:2008, Gas cylinders — Refillable welded steel cylinders — Test pressure 60 bar and below | This Uganda Standard specifies the minimum requirements concerning material selection, design, construction and workmanship, procedure and test at manufacture of refillable welded-steel gas cylinders of a test pressure not greater than 60 bar1), and of water capacities from 0.5 l up to and including 500 l exposed to extreme worldwide temperatures (-50 °C to 65 °C) used for compressed, liquefied or dissolved gases. Transportable large cylinders of water capacity above 150 l and up to 500 l may be manufactured and certified to this standard provided handling facilities are provided. This standard is primarily intended to be used for industrial gases other than Liquefied Petroleum Gas (LPG), but may also be applied for LPG. For specific LPG applications see ISO 22991. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 20345: 2011, Personal protective equipment — Safety footwear | This Uganda Standard specifies basic and additional (optional) requirements for safety footwear used for general purpose. It includes, for example, mechanical risks, slip resistance, thermal risks, ergonomic behaviour. Special risks are covered by complementary job-related standards (e.g. footwear for firefighters, electrical insulating footwear, protection against chain saw injuries, protection against chemicals and molten metal splash, protection for motor cycle riders). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 5423:1992, Moulded plastics footwear — Lined or unlined polyurethane boots for general industrial use — Specification | This Uganda Standard specifies requirements for boots, moulded from polyurethane compound, for general industrial use. The boots may be either fabric-lined or tinlined and of any style from ankle boots to full thigh height inclusive. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
| US ISO 4643:1992, Moulded plastics footwear — Lined or unlined poly(vinyl chloride) boots for general industrial use — Specification | This Uganda Standard specifies requirements for boots, moulded from poly(vinyl chloride) compounds, for general industrial use. The boots may be either fabric-lined or unlined and of any style from ankle boots to full thigh height inclusive. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 14 September 2016 |
