English
FrançaisRegulations
Page 121 of 140, showing 20 records out of 2786 total, starting on record 2401, ending on 2420
| Title | Description | Implementation date | Source | Publication | Created |
|---|---|---|---|---|---|
| US 1025:2013, Moisture meters for cereal grain and oilseeds — Specification (2nd Edition) | This Uganda Standard specifies requirements for moisture meters for cereal grains and oilseeds, that is to say instruments measuring and indicating, either directly or by means of conversion tables and (or) correction tables, the moisture content of cereal grains and the moisture and volatile matter content of oilseeds. This standard applies only to moisture meters used for measurements on statistical samples. | 2013-10-25 | The Uganda National Bureau of standards | Uganda Gazette Vol. CV No. 54 of 25th October 2013 | 03 May 2017 |
| US 833-4:2013, Sawn softwood timber — Part 4: Brandering and battens — Specification | This Uganda Standard specifies requirements for one grade of timber suitable for use as brandering and battens intended for being fixed against beams and joists in roofs for the attachment of ceilings and for the boxing in of eaves, and for use as supports on roof trusses for the fixing of roofing slates, tiles, wooden shingles and thatch. | 2014-01-27 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVII No. 5 of JANUARY 2014 | 12 April 2017 |
| US 1501:2013, Fresh onions — Specification | This Uganda Standard specifies requirements for onions of varieties (cultivars) grown from Allium cepa L. to be supplied to the consumer in the natural state. This standard does not specify requirements for Bermuda onions, Creole onions, green onions with full leaves and onions for industrial processing. | 2013-10-25 | The Uganda National Bureau of standards | Uganda Gazette Vol. CV No. 54 of 25th October 2013 | 26 April 2017 |
| US 1501:2013, Fresh onions — Specification | This Uganda Standard specifies requirements for onions of varieties (cultivars) grown from Allium cepa L. to be supplied to the consumer in the natural state. This standard does not specify requirements for Bermuda onions, Creole onions, green onions with full leaves and onions for industrial processing. | 2013-10-25 | The Uganda National Bureau of standards | Uganda Gazette Vol. CV No. 54 of 25th October 2013 | 08 May 2017 |
| US 1501:2013, Fresh onions — Specification | This Uganda Standard specifies requirements for onions of varieties (cultivars) grown from Allium cepa L. to be supplied to the consumer in the natural state. This standard does not specify requirements for Bermuda onions, Creole onions, green onions with full leaves and onions for industrial processing. | 2013-10-25 | The Uganda National Bureau of standards | Uganda Gazette Vol. CV No. 54 of 25th October 2013 | 08 May 2017 |
| US 1501:2013, Fresh onions — Specification | This Uganda Standard specifies requirements for onions of varieties (cultivars) grown from Allium cepa L. to be supplied to the consumer in the natural state. This standard does not specify requirements for Bermuda onions, Creole onions, green onions with full leaves and onions for industrial processing. | 2013-10-25 | The Uganda National Bureau of standards | Uganda Gazette Vol. CV No. 54 of 25th October 2013 | 08 May 2017 |
| US 1502:2013, Fresh Bermuda onions — Specification | This Uganda Standard specifies requirements for onions of varieties (cultivars) of Bermuda-Granex-Grano grown from Allium cepa L. to be supplied to the consumer in the natural state. This standard does not specify requirements for Bermuda onions for industrial processing. | 2013-10-25 | The Uganda National Bureau of standards | Uganda Gazette Vol. CV No. 54 of 25th October 2013 | 26 April 2017 |
| US 1502:2013, Fresh Bermuda onions — Specification | This Uganda Standard specifies requirements for onions of varieties (cultivars) of Bermuda-Granex-Grano grown from Allium cepa L. to be supplied to the consumer in the natural state. This standard does not specify requirements for Bermuda onions for industrial processing. | 2013-10-25 | The Uganda National Bureau of standards | Uganda Gazette Vol. CV No. 54 of 25th October 2013 | 08 May 2017 |
| US ISO 13533:2001, Petroleum and natural gas industries — Drilling and production equipment — Drillthrough equipment | This Uganda Standard specifies requirements for performance, design, materials, testing and inspection, welding, marking, handling, storing and shipping of drill-through equipment used for drilling for oil and gas. It also defines service conditions in terms of pressure, temperature and wellbore fluids for which the equipment will be designed. | 2015-12-15 | The Uganda National Bureau of standards | The Uganda Gazette 22 January 2016: General Notice No. 45 of 2016 | 18 August 2016 |
| US ISO 973:1999, Pimento (allspice) [Pimenta dioica (L.) Merr.], whole or ground – Specification | This Uganda Standard specifies requirements for pimento or allspice [Pimentadioica (L.) Merr.], whole or ground. | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 02 September 2016 |
| US 998:2014, Plantain (gonja) — Specification | This Uganda standard specifies requirements for plantain (gonja) (AAB genome) banana grown from Musa spp. (AAA-B) and of family Musaceae. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 07 September 2016 |
| US 194-1:2016, Nails — Part 1: Steel nails — Specification | This Uganda Standard specifies requirements for preferred form and dimensions, tolerance on dimensions, finish and surface coating for the type of steel nails and of loose steel wire nails for general applications. | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US ISO 14732: 2013, Welding personnel — Qualification testing of welding operators and weld setters for mechanized and automatic welding of metallic materials | This Uganda Standard specifies requirements for qualification of welding operators and also weld setters for mechanized and automatic welding. | 2015-12-15 | The Uganda National Bureau of standards | 16 August 2016 | |
| US ISO 13710: 2004, Petroleum, petrochemical and natural gas industries — Reciprocating positive displacement pumps | This Uganda Standard specifies requirements for reciprocating positive-displacement pumps and pump units for use in the petroleum, petrochemical and natural gas industries. It is applicable to both direct-acting and power-frame types. | 2015-12-15 | The Uganda National Bureau of standards | The Uganda Gazette 22 January 2016: General Notice No. 45 of 2016 | 16 August 2016 |
| US ISO 18595:2007, Resistance welding — Spot welding of aluminium and aluminium alloys — Weldability, welding and testing | This Uganda Standard specifies requirements for resistance spot welding in the fabrication of assemblies of aluminium sheet, extrusions (both work- and age-hardening alloys) and/or cast material comprising two or three thicknesses of metal, where the maximum single (sheet) thickness of components to be welded is within the range 0,6 mm to 6 mm. This standard is applicable to the welding of sheets or plates of dissimilar thickness where the thickness ratio is less than or equal to 3:1. It applies to the welding of three thicknesses where the total thickness is less than or equal to 9 mm. Welding with the following types of machines is within the scope of this International Standard:pedestal welding machines;gun welders;automatic welding equipment where the components are fed by robots or automatic feeding equipment;multi-welders; androbotic welders | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 30 September 2016 |
| US ISO 14373:2006, Resistance welding — Procedure for spot welding of uncoated and coated low carbon steels | This Uganda Standard specifies requirements for resistance spot welding in the fabrication of assemblies of uncoated and metallic coated low carbon steel, comprising two or three sheets of metal, where the maximum single sheet thickness of components to be welded is within the range 0,4 mm to 3 mm, for the following materials: • uncoated steels; • hot-dip zinc or iron-zinc alloy (galvannealed) coated steel; • electrolytic zinc, zinc-iron, or zinc-nickel coated steel; • aluminium coated steel; ad • zinc-aluminium coated steel. This standard is applicable to the welding of sheets of the same or dissimilar thickness, where the thickness ratio is less than or equal to 3:1. It applies to the welding of three thicknesses, where the total thickness is less than or equal to 9 mm. Welding with the following types of equipment is within the scope of this standard: • pedestal welding equipment; • gun welders; • automatic welding equipment where the components are fed by robots or automatic feeding equipment; • multi welders; and • robotic welders. 12170). This standard does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 29 September 2016 |
| US ISO 14113:2013, Gas welding equipment — Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) | This Uganda Standard specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied, and dissolved gases up to a maximum working pressure of 450 bar (45 MPa), within the ambient temperature range of −20 °C to +60 °C. This standard applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage. This standard does not cover rubber or thermoplastic hoses for welding, cutting, and allied processes (see US ISO 3821 and US ISO 12170). This standard does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 14113:2013, Gas welding equipment — Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) | This Uganda Standard specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied, and dissolved gases up to a maximum working pressure of 450 bar (45 MPa), within the ambient temperature range of −20 °C to +60 °C. This standard applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage. This standard does not cover rubber or thermoplastic hoses for welding, cutting, and allied processes (see US ISO 3821 and US ISO 12170). This standard does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 29 September 2016 |
| US ISO 3821:2008, Gas welding equipment — Rubber hoses for welding, cutting and allied processes | This Uganda Standard specifies requirements for rubber hoses (including twin hoses) for welding, cutting and allied processes. This standard specifies requirements for rubber hoses for normal duty of 2 MPa (20 bar) and light duty [limited to hoses for maximum working pressure of 1 MPa (10 bar) and with bore up to and including 6,3 mm]. This standard applies to hoses operated at temperatures −20 °C to +60 °C and used in:⎯ gas welding and cutting;⎯ arc welding under the protection of an inert or active gas; and⎯ processes allied to welding and cutting, in particular, heating, brazing, and metallization.This standard applies neither to thermoplastics hoses nor to hoses used for high pressure [>0,15 MPa (>1,5 bar)] acetylene | 2015-04-21 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 17 September 2016 |
| US ISO 2928: 2003, Rubber hoses and hose assemblies for liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas up to 25 bar (2.5 MPa) — Specification | This Uganda Standard specifies requirements for rubber hoses and rubber hose assemblies used for the transfer of liquefied petroleum gas (LPG) in the liquid or gaseous phase and natural gas and designed for use at working pressures ranging from vacuum to a maximum of 25 bar (2.5 MPa) within the temperature range 30 °C to +70 °C or, for low-temperature hoses (designated -LT), within the temperature range −50 °C to +70 °C. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 04 October 2016 |
