English
FrançaisRegulations
Page 65 of 140, showing 20 records out of 2786 total, starting on record 1281, ending on 1300
| Title | Description | Implementation date | Source | Publication | Created |
|---|---|---|---|---|---|
| US ISO 6224:2011 Thermoplastics hoses, textile-reinforced, for general-purpose water applications — Specification | This Uganda Standard specifies the requirements for general-purpose textile reinforced thermoplastics water-discharge hoses. Three types of hose are specified according to their operating duty requirements, i.e. their ambient and water temperature ranges:ambient temperatures: −10 °C to +60 °C; and water temperature during operation: 0 °C to +60 °C. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 6804:2009, Rubber and plastics inlet hoses and hose assemblies for washing-machines and dishwashers — Specification | This Uganda Standard specifies the requirements for three types of rubber or plastics inlet hoses and hose assemblies for washing-machines and dishwashers connected to the domestic water supply at a pressure not exceeding 1 MPa (10 bar).It is applicable to the following types of hose: Type 1: rubber hoses for unheated water supply (maximum temperature 70 °C).Type 2: rubber hoses for heated water supply (maximum temperature 90 °C).Type 3: plastics hoses for unheated water supply (maximum temperature 60 °C). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 6807:2003, Rubber hoses and hose assemblies for rotary drilling and vibration applications — Specification | This Uganda Standard specifies the requirements for textile- and steel-reinforced rubber hoses and hose assemblies for use with water-based and/or oil-based muds, up to a maximum temperature of 82 °C, which are pumped at high pressure in large volumes in rotary drilling service and which, when tested in accordance with ISO 2977, have a minimum aniline point of 66 °C. This standard applies to hoses which are suitable for use at ambient temperatures between − 20 °C and + 52 °C, unless changed by a supplementary requirement on request of the purchaser, and are resistant to ageing and tropical conditions. This standard does not apply to hoses which are intended for use with gases.. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 8028:1999, Rubber and/or plastics hoses and hose assemblies for airless paint spraying — Specification | This Uganda Standard specifies the requirements for four types, differentiated by burst pressure and temperature of use, of elastomeric hose and hose assembly for use in airless paint spraying. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 8029:2007, — General-purpose collapsible water hose, textile reinforced — Specification | This Uganda Standard specifies the requirements for four types of textile-reinforced thermoplastics collapsible water hoses for general applications for use in the temperature range of−10 °C to +55 °C. Such hoses are classified into four types, as follows:low pressure, designed for a maximum working pressure of up to 4,0 bar at 23 °C and up to 2,0 bar at 55 °C;medium pressure, for a maximum working pressure of up to 7,0 bar at 23 °C and up to 3,6 bar at 55 °C;high pressure, for a maximum working pressure of up to 10,0 bar at 23 °C and up to 5,1 bar at 55 °C; andextra-high pressure, for a maximum working pressure of up to 15,5 bar at 23 °C and up to 7,9 bar at 55 °C.This standard does not apply to products used for fire-fighting or the conveyance of drinking water | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 8066-2:2001, Rubber and plastics hoses and hose assemblies for automotive air conditioning — Specification — Part 2: Refrigerant 134a | This Uganda Standard specifies the requirements for rubber or thermoplastic hoses and hose assemblies used for circulating liquid and gaseous R134a (tetrafluoroethane) in the air-conditioning systems of automobiles. The hoses and hose assemblies are designed in such a way as to restrict losses of refrigerant and contamination of the system. The operational temperature range is 40 °C to +125 °C | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 10380:2012, Pipework — Corrugated metal hoses and hose assemblies | This Uganda Standard specifies the minimum requirements for the design, manufacture, testing and installation of corrugated metal hoses and metal hose assemblies | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 11237:2010, Rubber hoses and hose assemblies — Compact wire-braid reinforced hydraulic types for oil-based or water-based fluids — Specification | This Uganda Standard specifies requirements for five types of compact, wire-braid-reinforced hose and hose assembly of nominal size from 5 to 31,5. They are suitable for use with water-based hydraulic fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging from −40 °C to +60 °C and oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C. This standard does not include requirements for end fittings. It is limited to requirements for hoses and hose assemblies. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 11424:1996, Rubber hoses and tubing for air and vacuum systems for internal-combustion engines — Specification | This Uganda Standard specifies requirements for vulcanized-rubber hoses and tubing for use in the various air and vacuum systems found on internal combustion engines. The standard does not cover hoses used for direct power-brake actuation in trucks and trailers, nor for air intakes and ducting within the passenger compartment. The highest-temperature hoses are generally used for turbocharger applications. All hoses and tubing remain serviceable down to - 40 “C. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 11425:1996, Rubber hoses and hose assemblies for automobile power steering systems — Specification | This Uganda Standard specifies requirements for five types of hose and hose assembly used in automobile power-steering systems, the five types differing in their pressure ratings and volumetric expansion. They are for use with fluids in the temperature range - 40 “C to + 135 “C. This standard is based on performance tests and, in order to take account of technological developments, no requirements are included for specific materials, detailed construction or manufacturing methods. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 12170:1996, Gas welding equipment — Thermoplastic hoses for welding and allied processes | This Uganda Standard specifies the requirements and relevant methods of measurement and testing of two types of thermoplastic hoses with maximum design working pressure of 1 MPa and of 2 MPa, used for flexible gas supply lines in specific fields of application as follows:small kits for brazing and welding in accordance with US ISO 14112;air-aspirated blowpipes for welding and allied processes;miniature welding such as jewellery work, dental work excluding acetylene applications; andarc welding with shielding gas. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 13363:2004, Rubber and plastics hoses for marine engine wet-exhaust systems — Specification | This Uganda Standard specifies requirements for three types and two classes of hose. The hoses are intended for use in marine-engine wet-exhaust systems (where the exhaust gases are mixed with the discharge of cooling water).The three types are:type 1: a softwall hose, made of oil-resistant material, with a synthetic-fabric reinforcement;type 2: a hardwall hose, made of oil-resistant material, with a synthetic-fabric reinforcement with a helical wire embedded in it; andtype 3: a hose or tube (flexible connector), made of oil-resistant material, with or without a reinforcement or cover, intended for use in short lengths in locations where the connector is protected from mechanical damage.The two classes are:class A intended for diesel engines; andclass B intended for petrol engines, and for diesel engines with a very high exhaust temperature | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 14113:2013, Gas welding equipment — Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) | This Uganda Standard specifies requirements for rubber and plastics hose and hose assemblies for use with compressed, liquefied, and dissolved gases up to a maximum working pressure of 450 bar (45 MPa), within the ambient temperature range of −20 °C to +60 °C. This standard applies to hose assemblies used to connect industrial gas cylinders to manifolds or bundles prior to any pressure reduction stage. This standard does not cover rubber or thermoplastic hoses for welding, cutting, and allied processes (see US ISO 3821 and US ISO 12170). This standard does not apply to refrigerated liquefied gases or to liquefied petroleum gases (LPG). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 14557:2002, Fire-fighting hoses — Rubber and plastics suction hoses and hose assemblies | This Uganda Standard gives requirements and test methods for rubber and plastics suction hoses for fire-fighting purposes. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 15465:2004, Pipework — Stripwound metal hoses and hose assemblies | This Uganda Standard specifies the requirements for the design, manufacture and testing of four principal types of stripwound metal hose and hose assemblies, of which only one type is for pressure applications. The four are: single overlap, unpacked and packed; double overlap, unpacked and packed, the last of these having maximum allowable pressures of up to 40 bar. These hoses and hose assemblies may be supplied in nominal sizes from DN 6 to DN 500 and may operate at temperatures up to 600 °C dependent on materials of construction | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 16438:2012, Agricultural irrigation equipment — Thermoplastic collapsible hoses for irrigation — Specifications | This Uganda Standard specifies requirements for reinforced and non-reinforced thermoplastic collapsible hoses, which are intended to be used as main and sub-main supply lines for the conveyance and distribution of water for irrigation at water temperatures up to 50 °C. It is applicable to irrigation hoses with nominal diameters between 40 mm and 500 mm and working pressures between 0,3 bar (0,03 MPa) and 6 bar (0,6 MPa). This standard is applicable to two types of hose configurations: distributor hose (with outlet connections) and plain hose (without outlet connections). | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 17165-1:2007, Hydraulic fluid power — Hose assemblies — Part 1: Dimensions and requirements | This Uganda Standard specifies requirements for hose assemblies that are manufactured from hoses that conform to US ISO 3949 and to all parts of US ISO 1436, US ISO 3862, US ISO 4079 and US ISO 11237 and hose fittings with elastomeric seals that conform to US ISO 12151-1, US ISO 12151-2, US ISO 12151-3 and ISO 12151-6. This part of US ISO 17165 contains information of the most important criteria for the selection of preferred types of hoses and hose fittings with elastomeric sealing for use in hydraulic fluid power applications. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 23297:2008, Thermoplastics hoses and hose assemblies — Wire or synthetic yarn reinforced single-pressure types for hydraulic applications — Specification | This Uganda Standard specifies requirements for eight classes and two types (construction with adhesive bond between layers and construction without adhesive bond between layers) of wire or synthetic yarn reinforced hydraulic hoses and hose assemblies of nominal size from 3,2 to 31,5. Each class has a single maximum working pressure for all sizes. Such hoses are suitable for use with hydraulic fluids HH, HL, HM, HR, and HV as defined in ISO 6743-4 at temperatures ranging from −40 °C to +100 °C for grades A and B and −40 °C to +120 °C for grades C and D. This standard does not include requirements for end fittings. It is limited to the performance of hoses and hose assemblies. The hose assembly maximum working pressure is governed by the lowest maximum working pressure of the components | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 669:2000, Resistance welding — Resistance welding equipment — Mechanical and electrical requirements | This Uganda Standard applies to resistance welding equipment, to guns with inbuilt transformers and to complete movable welding equipment. The following types are included: • single-phase equipment with alternating welding current; • single-phase equipment with rectified welding current by rectification of the output of the welding transformer; • single-phase equipment with inverter welding transformer; • three-phase equipment with rectified welding current by rectification of the output of the welding transformer; • three-phase equipment with a current rectification in the input of the welding transformer (sometimes called frequency convertor); and • three-phase equipment with inverter welding transformers. This standard applies neither to welding transformers sold separately nor to safety requirements | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 1089:1980, Electrode taper fits for spot welding equipment — Dimensions | This Uganda Standard lays down the taper dimensions and tolerances of electrode taper fits for spot welding electrode , electrode adaptors, electrode holders and similar parts. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
