English
FrançaisRegulations
Page 31 of 140, showing 20 records out of 2786 total, starting on record 601, ending on 620
| Title | Description | Implementation date | Source | Publication | Created |
|---|---|---|---|---|---|
| US EAS 334: 2013, List by category of cosmetic products | This Uganda Standard lays down the list of products that are classified as cosmetics. (This Uganda Standard cancels and replaces US 442-1:2002, Illustrative list by category of cosmetic products, which has been technically revised and republished). | 2014-01-27 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVII No. 5 of JANUARY 2014 | 12 April 2017 |
| US EAS 334: 2013, List by category of cosmetic products | This Uganda Standard lays down the list of products that are classified as cosmetics. | 2014-01-27 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVII No. 5 of JANUARY 2014 | 02 November 2016 |
| US ISO 5175:1987, Equipment used in gas welding, cutting and allied processes — Safety devices for fuel gases and oxygen or compressed air — General specifications, requirements and tests | This Uganda Standard lays down the general specifications, requirements of safety devices for fuel gases and oxygen or compressed air used downstream of cylinder or pipeline outlet regulators and of pipeline outlet valves, and upstream of blowpipes for welding, cutting and allied processes. lt does not specify location and combination of these devices in the gas system. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 28 September 2016 |
| US ISO 10431:1993, Petroleum and natural gas industries — Pumping units — Specification | This Uganda Standard lays down specification covering the design and rating of pumping units. | 2015-12-15 | The Uganda National Bureau of standards | The Uganda Gazette 22 January 2016: General Notice No. 45 of 2016 | 12 August 2016 |
| US IEC 61646: 2008, Thin-film terrestrial photovoltaic (PV) modules — Design qualification and type approval | This Uganda Standard lays down requirements for the design qualification and type approval of terrestrial, thin-film photovoltaic modules suitable for long term operation in general open-air climates as defined in IEC 60721-2-1. This standard is intended to apply to all terrestrial flat plate module materials not covered by US IEC 61215. (This Uganda Standard cancels and replaces US 553:2005, Thin film terrestrial PV (PV) modules – design qualification and type approval, which has been republished). | 2013-10-25 | The Uganda National Bureau of standards | Uganda Gazette Vol. CV No. 54 of 25th October 2013 | 03 May 2017 |
| US IEC 61215-2:2016, Terrestrial photovoltaic (PV) modules — Design qualification and type approval — Part 2: Test procedures | This Uganda Standard lays down IEC requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open air climates, as defined in IEC 60721-2-1. This part of US IEC 61215 is intended to apply to all terrestrial flat plate module materials such as crystalline silicon module types as well as thin-film modules. | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US IEC 61215-1-1:2016, Terrestrial photovoltaic (PV) modules — Design qualification and type approval — Part 1-1: Special requirements for testing of crystalline silicon photovoltaic (PV) modules | This Uganda Standard lays down IEC requirements for the design qualification and type approval of terrestrial photovoltaic modules suitable for long-term operation in general open air climates, as defined in IEC 60721-2-1 | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US US IEC 61215-1:2016, Terrestrial photovoltaic (PV) modules — Design qualification and type approval — Part 1: Test requirements | This Uganda Standard lays down IEC requirements for the design qualification and type approval of terrestrial photovoltaic (PV) modules suitable for long term operation in general open air climates, as defined in IEC 60721-2-1 | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US IEC 60086-1: 2011, Primary batteries — General | This Uganda Standard is intended to standardize primary batteries with respect to dimensions, nomenclature, terminal configurations, markings, test methods, typical performance, safety and environmental aspects. As a primary battery classification tool, electrochemical systems are also standardized with respect to system letter, electrodes, electrolyte, nominal and maximum open circuit voltage. This standard specifies test methods for testing primary cells and batteries. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 10 September 2016 |
| US ISO 16120-1:2011, Non-alloy steel rod for drawing and/or cold rolling — Part 1: General requirements | This Uganda Standard is applicable to wire rod of non-alloy steel intended for wire drawing and/or cold rolling. The cross-section can be circular, oval, square, rectangular, hexagonal, octagonal, half-round or another shape, generally with at least 5 mm nominal dimension, and with a smooth surface. | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US ISO 16120-3:2011, Non-alloy steel rod for drawing and/or cold rolling — Part 3: Specific requirements for nominal and rimmed substitute low carbon steel rod | This Uganda Standard is applicable to wire rod made of low-carbon, low-silicon, rimmed and rimmed substitute steel with high ductility intended for drawing and/or cold rolling. | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US ISO 16120-4:2011, Non-alloy steel rod for drawing and/or cold rolling — Part 4: Specific requirements for wire rod for special applications | This Uganda Standard is applicable to steel wire rod with improved characteristics intended for drawing and/or cold rolling. | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US IEC 60086-2: 2011, Primary batteries — Part 2: Physical and electrical specifications | This Uganda Standard is applicable to primary batteries based on standardized electrochemical systems. It specifies the physical dimensions and the discharge test conditions and discharge performance requirements. | 2015-04-21 | The Uganda National Bureau of standards | UGANDA GAZETTE Vol. CVIII No. 20 of 21 April 2015 | 10 September 2016 |
| US ISO 6742-4:2015, Cycles — Lighting and retroreflective devices — Part 4: Lighting systems powered by the cycle’s movement | This Uganda Standard is applicable to lighting systems used on cycles intended to be used on public roads and, especially, bicycles complying with US ISO 4210 and US ISO 8098. This part of US ISO 6742 specifies requirements and test methods for the performance of lighting systems powered by the cycle’s movement. It applies to light devices complying with US ISO 6742-1. Lighting systems include lighting devices and power supplied by cycle's movement such as generator. | 2015-12-15 | The Uganda National Bureau of standards | The Uganda Gazette 22 January 2016: General Notice No. 45 of 2016 | 10 August 2016 |
| US IEC 60095-1:2006, Lead-acid starter batteries — Part 1: General requirements and methods of test | This Uganda Standard is applicable to lead-acid batteries with a nominal voltage of 12 V, used primarily as a power source for the starting of internal combustion engines, lighting and for auxiliary equipment of internal combustion engine vehicles. These batteries are commonly called "starter batteries". This standard specifies general requirements; essential functional characteristics, relevant test methods and results required, for several classes of starter batteries; according to the general type of application; and according to the type of product. | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US IEC 60095-2:2009, Lead-acid starter batteries — Part 2: Dimensions of batteries and dimensions and marking of terminals | This Uganda Standard is applicable to lead-acid batteries used for starting, lighting and ignition of passenger cars and light vehicles with a nominal voltage of 12 V. | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US ISO 20187:2016, Inflatable play equipment — Safety requirements and test methods | This Uganda Standard is applicable to inflatable play equipment intended for use by children up to 14 years of age individually and as a group activity. This standard specifies safety requirements for inflatable play equipment for which the primary activities are bouncing and sliding. | 2017-02-03 | The Uganda National Bureau of standards | The Uganda Gazette, Vol. CX No. 7 | 22 March 2017 |
| US IEC 60889:1987, Hard-drawn aluminium wire for overhead line conductors | This Uganda Standard is applicable to hard-drawn aluminium wires for the manufacture of stranded conductors for overhead power transmission purposes. It specifies the mechanical and electrical properties of wires in the diameter range 1.25 mm to 5.00 mm. (This Uganda Standard cancels and replaces, US EAS 510:2008, Hard-drawn aluminium wire for overhead line conductors, which has been republished). | 2015-08-07 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVIII No. 43 of 7 August 2015 | 24 August 2016 |
| US ISO 16120-2:2011, Non-alloy steel rod for drawing and/or cold rolling — Part 2: Specific requirements for general purpose rod | This Uganda Standard is applicable to general-purpose steel wire rod for drawing and/or cold rolling. | 2016-08-12 | The Uganda National Bureau of standards | The Uganda Gazette Vol. CVIII No. 57 | 03 September 2016 |
| US IEC 60104:1987, Aluminium-magnesium-silicon alloy wire for overhead line conductors | This Uganda Standard is applicable to aluminium-magnesium-silicon alloy wires of two types having different mechanical and electrical properties for the manufacture of stranded conductors for overhead power transmission purposes. It specifies the mechanical and electrical properties of wires in the diameter range 1.50 mm to 4.50 mm. The two types are designated Type A and Type B respectively. (This Uganda Standard cancels and replaces US EAS 507:2008, Aluminium-magnesium-silicon alloy wire for overhead line conductors, which has been republished). | 2015-08-07 | The Uganda National Bureau of standards | THE UGANDA GAZETTE Vol. CVIII No. 43 of 7 August 2015 | 23 August 2016 |
